新的家用電動石磨機通常不太可能出現問題，但是在長期使用后，一定要做好家用電動石磨機的日常維護和校準維護工作，下面來具體講講內容吧。

The new household electric stone mill is usually unlikely to have problems, but after long-term use, we must do a good job in the daily maintenance and calibration maintenance of household electric stone mill. Let's talk about the content in detail below.

經常檢查軸承溫度。如果溫度過高，檢查潤滑和傳動部件是否正常，滾動距離是否過緊。及時查明原因，采取相應措施，嚴重時停止檢查。經常檢查傳動帶的松緊度。皮帶過松會降低傳動效率，影響磨削效果。如果皮帶過緊，容易造成軸承發熱，增加動力消耗，降低傳動皮帶的使用壽命。

Check the bearing temperature frequently. If the temperature is too high, check whether the lubrication and transmission parts are normal and whether the rolling distance is too tight. Find out the causes in time, take corresponding measures, and stop the inspection when it is serious. Always check the tightness of the drive belt. Too loose belt will reduce the transmission efficiency and affect the grinding effect. If the belt is too tight, it is easy to cause bearing heating, increase power consumption and reduce the service life of the transmission belt.

各種傳動部件必須緊固可靠，拆卸或安裝應使用專用工具，嚴禁用手錘等工具直接敲打。不要忘記檢查氣動元件。經常檢查氣路中的氣動元件，氣路和連接處是否有漏氣或損壞。同時檢查供氣壓力是否符合要求，經常檢查同步帶的使用情況，如發現過緊、過松、跳動、跑偏、磨損嚴重等，應及時調整、修理或更換。

All transmission parts must be fastened and reliable. Special tools shall be used for disassembly or installation. It is strictly prohibited to knock directly with tools such as hand hammer. Don't forget to check the pneumatic components. Always check the pneumatic components in the air circuit, whether there is air leakage or damage at the air circuit and connection. At the same time, check whether the air supply pressure meets the requirements, and regularly check the use of the synchronous belt. If it is found to be too tight, too loose, jumping, deviation, serious wear, etc., it shall be adjusted, repaired or replaced in time.

定期、有序地更換磨粉機的磨輥，一次磨輥不宜更換過多。同時，磨輥的直徑也不能相差太大。帶齒滾子的角度、傾角和齒數應符合規定，并預留一定量齒頂平面。光輥各段錐度應準確并符合規定要求，表面粗糙度應均勻。更換磨輥后，用塞尺檢查，根據各系統粉碎機的要求粗略調整滾動距離。

The grinding roller of the pulverizer shall be replaced regularly and orderly, and the primary grinding roller shall not be replaced too much. At the same time, the diameter of the grinding roller shall not differ too much. The angle, inclination and number of teeth of the toothed roller shall meet the requirements, and a certain amount of tooth top plane shall be reserved. The taper of each section of the smooth roller shall be accurate and meet the specified requirements, and the surface roughness shall be uniform. After replacing the grinding roller, check with a feeler gauge and roughly adjust the rolling distance according to the requirements of the crusher of each system.

每臺機器的相應位置應有相應的工作規范、操作規程和簡單的故障排除方法。制定所有設備臺賬，驗證（校準）周期表和計劃，并設置專人管理。正確使用和維護所有設備。具體維護和操作要點如下：

The corresponding position of each machine shall have corresponding working specifications, operating procedures and simple troubleshooting methods. Prepare all equipment accounts, verify (calibrate) periodic tables and plans, and assign special personnel to manage them. Properly use and maintain all equipment. Specific maintenance and operation points are as follows:

在日常維護和校準維護中，應密切關注影響檢測結果的因素，如灰塵、溫度、濕度、振動、噪音、腐蝕等因素，嚴格控制，減少誤差。必須保證所有機器工作臺面固定平整，符合使用要求。所有面粉機機器使用后應及時清洗和恢復，以保證下一次實驗的順利進行。

During routine maintenance and calibration maintenance, pay close attention to the factors affecting the test results, such as dust, temperature, humidity, vibration, noise, corrosion and other factors, and strictly control them to reduce errors. All machine worktops must be fixed and flat to meet the use requirements. All flour machines shall be cleaned and restored in time after use to ensure the smooth progress of the next experiment.

電氣設備應安裝與額定功率一致的獨立電源開關，并有良好的接地線。個別石磨設備應按說明書要求配備穩壓電源。使用機器的相關人員應學習相應的法律、法規和管理制度，所有操作人員均應取得資格證書或接受過機器操作培訓。

The electrical equipment shall be equipped with independent power switch with the same rated power and good grounding wire. Individual stone grinding equipment shall be equipped with regulated power supply according to the requirements of the manual. Relevant personnel using the machine shall learn relevant laws, regulations and management systems, and all operators shall obtain professional qualification certificates or receive machine operation training.

總之，這些操作都是可以避免家用電動石磨機的磨損，有利于延長機器的使用壽命。更多相關內容的了解就來網站www.yudikj.com進行咨詢吧！

In short, these operations can avoid the wear of household electric stone mill and prolong the service life of the machine. For more information, please visit www.yudikj.com Com for consultation!